The RMALDCBS1X16 GPS/GNSS Rack Mount Amplified Splitter is a one input, eight output device. The frequency response covers all GPS/GLONASS/GALILEO bands with excellent gain flatness. In the normal configuration, the splitter is powered by a transformer that supplies power to the splitter’s amplifiers and roof antenna. The outputs are DC loaded with 200 Ohm resistors to simulate the antenna current draw. Product is ideal for timing and testing applications where the GPS carrier signal is required by up to 16 GPS/GNSS devices simultaneously.

The ALDCBS1X2 GPS Amplified Splitter is a one input, two output device with a 20dB min. gain block. The frequency response covers the GPS L1, L2 and GLONASS bands with excellent gain flatness. In the normal configuration, the splitter RF output (J1) passes DC from the connected GPS receiver through the splitter to the antenna, allowing the GPS receiver to power both the antenna and the splitter amplifier. The other RF output (J2) is DC loaded with a 200 Ohm resistor to simulate the antenna current draw.

The LDCBS1X2 GPS antenna splitter is a passive one input two output power divider designed specifically for the GPS L1, L2 & GLONASS carrier frequencies. One of the output legs (J2) is DC-Blocked to prevent antenna damage, it also has a 200 ohm DC load to ground to simulate a GPS antenna pre-amplifer current draw. The other output leg (J1) is a DC through to power the antenna.

The MIL-NLDCBS1X3 GPS antenna splitter is a one input three output power divider designed specifically for the GPS L1, L2 and GLONASS carrier frequencies. The three output legs (J2-J4) are DC-Blocked to prevent antenna damage. J2 & J3 are TNC connectors and J4 is a N-type connector, J4 also has 5db of attenuation inline. This splitter has been designed and built to military specifications.

The RMALDCBS1X32 GPS/GNSS Rack Mount Amplified Splitter is a one input, eight output device. The frequency response covers the all GPS/GLONASS/GALILEO bands with excellent gain flatness. In the normal configuration, the splitter is powered by a transformer that supplies power to the splitter’s amplifiers and roof antenna. The outputs are DC loaded with 200 Ohm resistors to simulate the antenna current draw. Product is ideal for timing and testing applications where the GPS carrier signal is required by up to 32 GPS/GNSS devices simultaneously.

The ALDCBS1X4 GPS Amplified Splitter is a one input, four output device with a 17dB min. gain block. The frequency response covers the GPS L1, L2 and GLONASS bands with excellent gain flatness. In the normal configuration, the splitter RF output (J1) passes DC from the connected GPS receiver through the splitter to the antenna, allowing the GPS receiver to power both the antenna and the splitter amplifier. The other RF outputs (J2, J3, J4) are DC loaded with 200 Ohm resistors to simulate the antenna current draw.

The LNFA1X4 is a low noise, filtered, amplified 1X4 GPS antenna splitter that was originally designed to satisfy AT&T Wireless requirements. The device features high selectivity for protection against the proximity of high power cellular transmitters.

The LDCBS1X4 GPS antenna splitter is a passive one input four output power divider designed specifically for the GPS L1, L2 & GLONASS carrier frequencies. Three of the output legs (J2-J4) are DC-Blocked to prevent antenna damage, they also have 200 ohm DC loads to ground to simulate a GPS antenna pre-amplifier current draw. The other output leg (J1) is a DC through to power the antenna.

The ALDCBS1X8 GPS Amplified Splitter is a one input, eight output device with 13dB min. gain block. The frequency response covers GPS L1, L2 & GLONASS bands with excellent gain flatness. In the normal configuration, the splitter RF output (J1) passes DC from the connected GPS receiver through the splitter to the antenna, allowing the GPS receiver to power both the antenna and the splitter amplifier. The other RF outputs (J2 - J8) are DC loaded with 200 Ohm resistors to simulate the antenna current draw.

The RMALDCBS1X8 GPS/GNSS Rack Mount Amplified Splitter is a one input, eight output device. The frequency response covers the GPS L1 & L2 bands with excellent gain flatness. In the normal configuration, the splitter is powered by a transformer that supplies power to the splitter’s amplifiers and roof antenna. The outputs are DC loaded with 200 Ohm resistors to simulate the antenna current draw. Product is ideal for timing and testing applications where the GPS/GNSS carrier signal is required by up to 8 GPS/GNSS devices simultaneously.